Image-I Adapter

Drivers
ia32v211.exe    Image/A & Image-i OS/2 Drvr (2.1x-BETA)
iadsp211.exe     Image/a & Image-i Dsp. Sprt. (required)
ia16v210.exe    Image/a & Image-i OS/2 16bit drivers
iaopt211.exe     Image/a & Image-i Opt Dsk(inc new 76/77 )
iawin210.exe     Image/a & Image-i Windows 3.x drivers
iados210.exe     Image/a & Image-i DOS AI&AutoCAD drvrs

       A Printer/Scanner Option (#1632) is available with the adapter allowing the direct attachment of the following devices:
o   IBM 3812 Printer Model 002 with Image Feature (#4050) or IBM 4216 Personal Pageprinter Model 020
o   IBM 3117 Scanner with extension unit (PN 6456808) or IBM 3118 Scanner or Bell & Howell 2115I (1) Scanner or equivalent
       IBM PS/2 Image Adapter/A enables both a scanner and a printer to be attached at one time via this optional printer/scanner daughter card. Use of the Printer/Scanner Option does not require an extra system unit slot.

9504 Monochrome Monitor (2)
6091-016 Color Display
6091-19i Color Display
1091 Color Display
9517 Color Display.

The Image-I Adapter/A is available in 3MB only, is ISO enabled, supports only ISO refresh rates and coexists with VGA on planar, XGA/XGA-2 chipset on planar, XGA/XGA-2 Adapter/A card

The Image-I Adapter/A can be installed in any 386, -SX, -SLC, 486SX, 486 or higher systems .

The Image-I Adapter/A can not be installed in the Model P70 386 (8573), .does not support the Image Adapter/A Printer/Scanner Option, and only one IBM PS/2 Image-I Adapter/A can be installed in a system unit.
VGA data display can only be achieved if the Image-I Adapter/A is installed in the AVE slot. Image-I Adapter/A may not be installed in slots with the matched memory extension.

The display attached to the Image Adapter can show VGA graphics only if the adapter is installed in the AVEC slot. Ideally, the Image Adapter should be installed in the AVEC slot unless this slot is already in use (e.g. with an 8514/A Adapter)

6019-019 Display Cable
This cable is required if the Image-I Adapter/A is supporting a 6019-019.

`Pin`	`Type`	`No Serial`	`Serial Captured Cable`
`C1`	`Coax`	`Red BNC`	`Red 75 Ohm Terminator`
`C2`	`Coax`	`Green BNC`	`Green 75 Ohm Terminator`
`C3`	`Coax`	`Blue BNC`	`Blue 75 Ohm Terminator`
`1`	`TP`	`ID Pin 2`	`ID Pin 2`
`2`	`TP`	`ID Pin 1`	`ID Pin 1 /Clk Out`
`3`	`TP`		`H.V.S.D.`
`4`	`Coax`	`Digital Ground`	`Digital Ground`
`5`	`Coax`	`Hsync BNC`	`Hsync`
`6`	`TP`	`ID Pin 4`	`ID Pin 4`
`7`	`TP`	`ID Pin 3`	`ID Pin 3 / Data`
`8`	`TP`
`9`	`Coax`	`Vsync BNC`	`Vsync`
`10`	`Coax`	`Digital Ground`	`Digital Ground`

DMA Arbitration Level
Under normal circumstances, select 5, this is an arbitary decision!
<"Level 5">, 6, 7, 8, 9, 10, 11, 12, 13, 14, 0, 1, 2, 3, 4

Fairness On/Off
Whether the adapter releases control of the bus when it has been using it exclusively
<"On">, Off

Adapter I/O Addressing
<"I/O Addresses 1D00-1D7F">, 2D00-2D7F, 3D00-3D7F, 4D00-4D7F

Adapter Memory Location
Memory location adapter uses for the BIOS ROM, and RAM window
<"Segment C000" (C000-C1FF)>, C200 (C200-C3FF), C400 (C400-C5FF), C600 (C600-C7FF), C800 (C800-C9FF), CA00 (CA00-CBFF), CC00 (CC00-CDFF), CE00 (CE00-CFFF), D000 (D000-D1FF), D200 (D200-D3FF), D400 (D400-D5FF), D600 (D600-D7FF), D800 (D800-D9FF), DA00 (DA00-DBFF), DC00 (DC00-DDFF), DE00 (DE00-DFFF)

Extended Memory Window
Some applications may require an Extended Memory Window into Image Adapter/A RAM to appear high in the system address space.
<"Disabled">, 1 Meg at Address E00000 (e000-eFFF), D00000 (d000-dFFF), C00000 (c000-cFFF), B00000 (b000-bFFF), A00000 (a000-aFFF), 900000 (9000-9FFF), 800000 (8000-8FFF), 700000 (7000-7FFF), 600000 (6000-6FFF), 500000 (5000-05FFF), 400000 (4000-4FFF), 300000 (3000-3FFF), 200000 (2000-2FFF), 100000 (1000-1FFF), 2 Meg at Address D00000 (d000-eFFF), C00000 (c000-dFFF), B00000 (b000-cFFF), A00000 (a000-bFFF), 900000 (9000-aFFF), 800000 (8000-9FFF), 700000 (7000-8FFF), 600000 (6000-7FFF), 500000 (5000-6FFF), 400000 (4000-5FFF), 300000 (3000-4FFF), 200000 (2000-3FFF), 100000 (1000-2FFF)