PC Server 500 (8641) Power Supplies

Main PSU and Additional PSU
Connecting the Additional PSU (220W)
   Connect ACO Connector
   Connect Signal Cable
   Re-Installing the primary power supply cover plate
220W Power Supply Unmasked!
Using 220W PSU as Seperate Power Supply
   Signal Cable Voltage Source
Primary Power Supply Voltages

Main PS and Additional PS


Connecting the 220W Power Supply
   The Type 86XX computers are shipped with a 434W primary power supply. An additional or optional 220W power supply can be added to the computer. This "optional" power supply MUST be installed if you are going to put a second RAID bacplane and drives in! Connectors are used to transfer the primary power supply voltages and signals from the primary power supply to the optional power supply. 


Connect ACO Connector
Unplug the power cord!!! 

   Remove the primary power supply cover plate retaining screw. Push the cover plate inwards until it stops (about 3/8 of an inch). Pull up on the edge now overhanging the side of the power supply. Note the tab and slot locking arrangement. 

   Pull the ACO connector out of the power supply. It won't come out very far, just enough for the plug body to clear the PS case. DO NOT attempt to pull the ACO connector cable out farther! The connector cable is short and it's tied to the power supply frame as well. Connect the ACO connector from the 220W power supply. Push both connectors back into the recess of the primary power supply. 



Connect Signal Cable
 From the 500 Man
The signal cable from the 220W PSU plugs onto the four pin header on the side near the front of the primary 434W PSU. It turns on the 220W PSU. 

  In short, plug the signal cable onto the four pin header in the main PSU. 

   Slide the 220W power supply onto the locking tabs. Slide it towards the rear of the system until it stops. Fasten the 220W PS to the main PS with the two screws through the mounting tabs on the 220W power supply. 



Re-Installing the primary power supply cover plate
 Caution
    When replacing the primary power supply cover plate, rotate the plate 180±. This will leave an opening for the primary power supply connector cable that connects to the optional power supply.  Failure to do so will cause the power supply connector cable to be crimped when the plate is replaced. 

   Rotate the cover plate so the downward part enters the recess first. Ensure that the locking tabs are in the slots. Push the cover forward until the cover plate mounting screw can be inserted. Fasten the cover down with a screw. 

  When you rotate the cover, you may not be able to slide it far enough for the mounting screw hole in the plate to match up with the tapped hole in the power supply. Take a file and remove enough of the metal from the downward length on the side towards the exhaust end of the power supply. It is marked "X" in the illustration. You don't need to remove much. 



220W Power Supply Unmasked!


Using 220W PSU as Seperate Power Supply
Brent R. Carlson wrote:
  After about an hour of trying different things here is how I GOT IT TO
TURN ON! Apply +12v to the Yellow and Grey while using the White as ground. I tried 5v to start but no go. (Ed. talking about signal cable)
   3 wires 9 combinations at each voltage, I'm glad Astec did not use a mix
of voltage ie: +5 on the Yellow and +12 on the Grey or some variation if
they had I would still be working on it.

BTW: I'm using the PSU to power a peltier, because of it's high current
requirements this PSU was ideal for the job. 84w Peltier 12 volt @ 8 A.

Signal Cable Voltage Source
  Originally, I asked Brent where he got the +12v from. I thought it was out of the 220W PSU. How could it be, since the 220W PSU needs that sense voltage to turn on in the first place.... Duh....

Brent replies:
   I took 12 volts from my current ATX supply.


Primary Power Supply Voltages
If the voltages are correct, and the power supply fan runs, the power supply is OK. 
-Lead Pin  +Lead Pin  Vdc Min  Vdc Max 
    5          3        +3.7    + 6.2 
    5          4        +9.0    +15.0
    5          7        -9.0    -15.0
    B          D        +3.7    + 6.2
    B          A        +9.0    +15.0 
 
 


Fan Assembly Power Connectors P11, P12, and P13 
  PICTURE 45
 -Lead Pin   +Lead Pin  Vdc Min  Vdc Max 
     2           1       +11.5    +12.6 

9595 Main Page